Exactly how to Replace a Bath Tub (Step By Step).
Exactly how to Replace a Bath Tub (Step By Step).
Blog Article
Have you been in search of content about A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't specifically rocket science, however it does require solid plumbing, woodworking, and sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably hard job. If the old bathtub is readily available, the job can relocate quickly; if you need to open up a wall surface to remove the old bathtub and also position the new bath tub, the task is much harder. In either situation, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old bathtub and embeded in the new one. Ensure you have certified on your own for the work and are comfortable trying it. Rather than employing a service provider to take over a halfway-completed project, it is much better to think about using one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This write-up will aid you set up a new bathtub in your restroom if you have actually currently acquired a brand-new bathtub as well as do not require to change the arrangement of your previous supply of water pipes.
Your tools as well as product list need to consist of the following:
Preparing for the Installation
First of all, the supporting framework supplied with the bathroom ought to be fitted (if required) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to avoid stress on the tub.
Fit the flexible tap connectors to the bottom of both taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should now be ready to be fitted in its last position.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is detach the water supply. After doing so, switch on the taps to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the restricted accessibility that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth all set for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from turning throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in uniformly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the spirit level checks out degree.
To install taps, fit the bottom of the outermost flexible tap port to the ideal supply pipe by making a compression join; then do the very same for the other faucet.
Switch on the water supply and also check all joints and also new pipework for leakages and tighten them if essential. Load the bath tub as well as also inspect the overflow electrical outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's user's manual. Tiling and also sealing around the bathtub ought to wait up until the tub has actually been made use of at the very least when as this will certainly settle it into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in area in between the faucet and also the sink. Secure the tap in place with the manufacturer supplied backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The previous type ought to be attached to the faucet ends initially, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to break a stiff seal, causing the water to penetrate the wall surface in between the bath and the tiling, bring about problems with dampness and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and also installations. They are offered in tubes and cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily readily available on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that write-up about How to Install a Bathtub Yourself through someone on our other site. Sharing is good. Who knows, you may be doing someone a favor. We thank you for reading our article about A Step-by-Step Guide to Installing a Bathtub.
Visit Website Report this page